tayadetroit.blogg.se - Smart shooter 3 v3.15 windows full download

Smart shooter 3 v3.15 windows full download update#
Smart shooter 3 v3.15 windows full download software#
Smart shooter 3 v3.15 windows full download code#
Smart shooter 3 v3.15 windows full download Pc#
Smart shooter 3 v3.15 windows full download download#

B must use Tesira firmware 4.2.2 or later. All TesiraFORTÉ AVB processors marked Rev.

Added support for updated components in TesiraFORTÉ AVB processors.

B TesiraFORTE AI models could be slow to respond in certain layouts that use a lot of DSP resources. B would not start on boot and require a power cycle.

Resolved rare issue where TeisraFORTÈ Rev.

B could show “Internal SW Error(m)” on boot.

Resolved rare issue where TesiraFORTÈ Rev.

Resolved rare issue where TesiraFORTÈ X could show wrong MAC addresses on wrong ports.

Resolved issue where multiple Parlè Mics connected to a TesiraCONNECT result in mic capsule fault conditions.

Resolved issue where Dante flows could lose channel names due to reboot, layout change, or network change.

Resolved issue where Dante audio could have crackling when using TesiraCONNECT TC-5D as Dante media master.

Resolved issue where Dante input audio could click every half-second.

Resolved issue where TesiraFORTÈ X could show “Dante card failed to sync clock to backplane” when AVB is set as the clock master.

Resolved issue where factory reset would result in Dante card not resetting to Tesira default hostname.

Updates Dante implementations to Dante version 4.2.3.x.

Added minor fault message for when NTP is configured but cannot get time from the server.

Support for pre-existing processors is maintained in this firmware version. B must use Tesira firmware 4.2.3 or later. All TesiraFORTÉ DAN processors marked Rev.

Added support for updated components in TesiraFORTÉ DAN (Rev.

Smart shooter 3 v3.15 windows full download software#

Released April 2022, Firmware-only release, aligned with software release 4.2.2 Resolved issue in which Tesira software could lose its control connection resulting in devices hanging and rebooting.Resolved issue with TesiraFORTE X models not receiving AES67 streams.Resolved issue where Tesira EX-UBTs connected across multiple TesiraConnects would have intermittent AVB stream drops.Resolved issue where VoIP log would not clear a “Not Registered” fault.Resolved issue on TesiraFORTE X where the web UI would show the wrong IP Gateway.Resolved issue in which DHCP lease time not shown in TTP response for network info.Resolved issue where ethernet traffic could show up on the wrong ports on TesiraFORTE X.Resolved issue where devices running Tesira 4.0 and newer could lose network connectivity after DHCP lease renewal.Resolved issue where Tesira XEL Amplifiers would drop AVB Streams or become undiscoverable after reboot.TesiraFORTE DAN models would only pass 2 or 4 channels of Dante audio. Resolved issue where Tesira Software would report 100% DSP utilization on Server IO DSP-2 card when it was not using 100%.Resolved issue where changing the channel count on a Parlé Processing block could cause Tesira Software to restart.Resolved issue where Tesira Software could crash when a VoIP X block was selected in “Server Only” mode.Added support for Rev B models of TesiraFORTE X and TesiraCONNECT TC-5 and TC-5D.Added ability to set IP Settings on Media Interface on NPX Paging devices.Added Dante Fault reporting on all TesiraFORTE X and TesiraFORTE DAN models.Added new entries in the processing library for the new Desono EX-S6, EX-S8, EX-S10, and EX-S10SUB speakers.Resolved issue where a TesiraFORTE X may transmit a RSTP packet during boot even though RSTP is disabled.Resolved issue with incorrect channel routing in TesiraXEL after running locate.Resolved issue where VoIP X transmit packets with high jitter cause audio drops.Resolved issue of compilation errors after adding a VoIP X block.Added USB connect and disconnect messages to event logs for all products.

Smart shooter 3 v3.15 windows full download download#

The event logs download now includes a new TTP (Tesira Text Protocol) log that provides information to assist troubleshooting control automation behavior.

NPX paging station LCD now displays “Ready for configuration …” when unconfigured.NPX in AVB mode no longer requires dynamic VLANS (MVRP).

Smart shooter 3 v3.15 windows full download code#

Added support for page code labels and preamble/recorded message labels in the following languages:.

NPX media type can now be changed without having to delete all page and zone control elements.

Added custom message slot protection option to prevent users from overwriting important messages when recording local messages.

Smart shooter 3 v3.15 windows full download Pc#

NPX Paging Stations on separated networks in AVB mode can now be setup from a PC with a single network inteface.Added page active logic output from the Paging Zone block to signal when a page is active in a zone.

Smart shooter 3 v3.15 windows full download update#

The update process is detailed here: Normal Tesira firmware update procedure. This article provides details of Tesira Software and Firmware revisions as well as Biamp Canvas revision notes.